Allow the test cassette, specimen, and/or controls to reach room
temperature (15-30ºC) prior to testing. Instruct the donor to not
place anything in the mouth including food, drink, gum or tobacco
products for at least 10 minutes prior to collection.
1. Bring the pouch to room temperature before opening it. Remove
the test cassette from the sealed pouch and use it within one hour.
2. Remove the collector from the sealed pouch and insert the sponge
end of the collector into the mouth. Actively swab the inside of
the mouth and tongue to collect oral fluid for a total of 3 minutes
until the sponge becomes fully saturated. Gentle pressing the
sponge between the tongue and teeth will assist saturation. No hard
spots should be felt on the sponge when saturated.
3. Remove the collector from the mouth. Place saturated oral fluid
collector into chamber and press sponge fully against the strainer
to collect oral fluid. Discard the collector. Snap the cap shut on
the collection tube.
4. Place the test cassette on a clean and level surface. Unscrew
cap cover from the collection tube. Invert the collection tube and
transfer 3 drops of oral fluid (approximately 120 µL) into specimen
well of the test cassette and start the timer. Avoid trapping air
bubbles in the specimen well. Place screw cap on the collection
tube. See illustration below.
5. Wait for the colored line(s) to appear. Read results at 10
minutes. Do not read results after 1 hour.
6. Apply the security seal over screw cap and send to the
laboratory for confirmation if necessary.
DIRECTIONS FOR DEVICE USE
Allow the test device, specimen, and/or controls to reach room
temperature (15-30ºC) prior to testing. Instruct the donor to not
place anything in the mouth including food, drink, gum or tobacco
products for at least 10 minutes prior to collection.
1. Bring the pouch to room temperature before opening it. Remove
the test device from the sealed pouch and use it within one hour.
2. Insert the absorbent wick to the mouth and put it under the
tongue to collect oral fluid until the control line appears.
3. Place the test device on a clean and level surface. See
illustration below.
4. Read results at 10 minutes. Do not read results after 15
minutes.
INTERPRETATION OF RESULTS
(Please refer to the illustration above)
NEGATIVE:* Two lines appear. One colored line should be in the
control line region (C), and another apparent colored line should
be in the test line region (T). A negative result indicates that
the Synthetic Marijuana metabolite concentration is below the
detectable level (25ng/mL).
*NOTE: The shade of color in the test line region (T) may vary, but
it should be considered negative whenever there is even a faint
colored line.
POSITIVE: One colored line appears in the control line region (C).
No line appears in the test line region (T). A positive result
indicates that the Fen/tanyl (FYL) concentration exceeds the
detectable level (50 ng/mL/20ng/ml).
INVALID: Control line fails to appear. Insufficient specimen volume
or incorrect procedural techniques are the most likely reasons for
control line failure. Review the procedure and repeat the test
using a new test. If the problem persists, discontinue using the
lot immediately and contact your local distributor.
Order Information
| Cat. No. | Product | Specimen | Pack |
| DFY-102 | Fen/tanyl (FYL) Rapid Test Cassette | Urine | 40 T |
| DFY-114 | Fen/tanyl (FYL) Rapid Test Panel | Urine | 40 T |
| DFY-101 | Fen/tanyl (FYL) Rapid Test Dipstick | Urine | 50 T |
| DFY-802 | Fen/tanyl (FYL) Rapid Test Cassette | Oral Fluid | 25 T |
| DFY-803 | Fen/tanyl (FYL) Rapid Test Device | Oral Fluid | 25 T |
| DFY-402 | Fen/tanyl (FYL) Rapid Test Cassette | WB/S/P | 40 T |
| DFY-X14 | Fen/tanyl (FYL) Rapid Test Panel | Powder | 25 T |
